Two-way recipe

Before you start, be sure to read all points un iepāzīstieties ar tiem!
1. Cover the table with an unnecessary cloth or film, it is recommended to wear a handkerchief.
2. Remove all contents from the container.
3. Before starting work, decide what shape you want to cast. Lower your hands to empty the bucket, to understand how much free space you have and how to better satvert your hands so that the tank does not fall to the walls.
4. Add 2 liters of water to the bucket (16-20 ° for water) . Do not add a warmer, it will change its mass during curing. The water will be too warm, the mass will dry very quickly, and you will not be able to mix it properly. So check the water temperature with a thermometer or add hot water.
5. Iemasējiet rocks or cosmetics or sildaņu ųlu (also augu ųų ir įptaų).
6. Then pour all the alginate powder into the water and stir with a spoon or kitchen whisk at the same time. Do it very actively, only 60-70 seconds are allotted for it.
7. So that the mass becomes hard, slowly lower your hands into the mass in the same position as you have previously chosen at the bottom, the bottom of the spatula, slightly lift it up. Make sure you don't touch the ceiling or the walls.
8. Try not to move your hands for 3 to 4 minutes (if you pour hot water into it, you will have to continue for longer), until the mass is completely saturated and becomes rubbery.
9. Carefully remove the rocks one at a time, being careful not to damage the existing rock forms.
10. Put the gypsum powder in another container and pour 700ml. room temp water
11. Put on disposable gloves and start mixing thoroughly with both hands. Move, actively, his chest thickens rapidly.
12. To make sure that the gypsum is mixed properly, add 1/2 of the gypsum to form the hollow shape of the palm.
13. Take the bucket or both hands and turn and press the walls of the bucket at a 45° angle, so that the plaster fills all hard-to-reach places.
14. Fill the cavity of the molds up to the top, do not overfill, rather touch the walls of the bucket, smash the bucket against the bottom of the table to get rid of as many air bubbles as possible.
15. Now wait 1-2 hours for the plaster to cure. (do not store for more than 3 hours).
16. Carefully turn the bucket upside down and take it out.
17. Carefully apply the alginate mass, taking care not to damage the sculpture.
18. Use any cleaning agent to remove alginate waste and prevent unnecessary stains caused by air bubbles.
19. Now that the sculpture is cleaned and prepared, we recommend leaving it in a dry, safe place for one day and letting it dry properly. After 5-7 days, the sculpture will completely dry and become completely white. completely white, so you can paint it to protect the plaster. Paint 2-3 very thin layers . Choose a soft brush.
---------------------------------------------------- ---------------------------------------------------- ------
Additional information un padomi:
1. Fill the required amount of water, lower your hands and try, practice the first step, you will see where your hands will be immersed, so that will be your place.
2. Make sure your hand is not touching the bottom of the wall.
3. The height of the bucket included in the set is not sufficient for the desired shape of the rock, you can choose your own container, but the water volume must remain the same as indicated in the instructions.
4. Izvairieties place the figures or close up with the fingers drawn up, the ends of the fingers will burn. Kabatinų un ďipša maisījums will not fill them. Do not place palms or outstretched fingers.
5. Never mix alginate powder or water that is warmer than 22 °C!
6. Mix the alginate mixture very quickly, it only takes 50-60 seconds! Use a kitchen whisk.
7. Try to mix in such a way that you do not leave dry powder on the bottom of the bucket. Active mixing is also very important.
8. In order for the mixture to be properly prepared, add rock or oil (this can be done before mixing). put the hands in the bucket without touching the bottom of the walls.
9. Slowly place the rocks in the bucket to prevent many air bubbles from forming.
10. After 3 - 4 minutes, touch the mass with your free hand to make sure that it is properly saturated.
11. Pour the plaster in two layers.
12. All the stages of filling should be carefully mixed in a bucket so that the plaster is properly filled in all cavities at the same time, getting rid of unwanted air bubbles.
13. Fill the entire cavity with plaster or plaster, do not overfill.
14. Wait at least 1 hour for the gypsum to harden.
15. Your nails are also quite strong, be very careful around the tip of your finger, you can break the shape of the tip of the nail or even the larger part of the finger.
16. Your figure will completely dry out after 7 days. It will turn completely white.
17. Paint only when it is completely dry.
****************************************************** ******************************************
This guide is compiled based on many tests, so follow all the points carefully, and you will be satisfied with the end result!